the illustration figure, which is prepared for a func-
tional group, subfunctional group, or an assembly.
H The lowest maintenance level capable of com-
plete repair of the support item is the general
4. Special Information
a. The following publication pertains to the AN/
Z Nonreparable. No repair is authorized.
PTM-7 and its components:
(3) Recoverability code. Recoverability codes
TM 11-5965-206-145 Headset-Microphone H-
are assigned to support items to indicate the disposi-
91A/U; Handset-Headset H-144/U, H-144A/U,
tion action on unserviceable items. The recoverabil-
H-144B/U, and H-144C/U; and Headset-
ity code is entered in the fifth position of the Uniform
SMR Code format as follows:
TM 11-6625-648-12, Test Set, Telephone AN/PTM-
TM 11-6625-648-45, Test Set, Telephone AN/PTM-
Z Nonreparable item. When unserviceable, con-
b. National stock numbers (NSN's) that are miss-
demn and dispose at the level indicated in posi-
ing from P source coded items have been applied for
and will be added to this TM by future change/
F Reparable item. When uneconomically repara-
revision when they are entered in the Army Master
ble, condemn and dispose at the direct support
Data File (AMDF). Until the NSN's are established
and published submit exception requisitions to
H Reparable item. When uneconomically repara-
ble, condemn and dispose at the general sup-
Command and Fort Monmouth, ATTN: DRSEL-
MM, Fort Monmouth, NJ 07703 for the part re-
c. National Stock Number. Indicates the National
quired to support your equipment.
stock number assigned to the item and will be used
for requisitioning purposes.
5. How to Locate Repair Parts
d. Federal Supply Code for Manufacturer (FSCM).
a. When National stock number or part number is
The FSCM is a 5-digit numeric code listed in SB
708-41/42 which is used to identify the manufac-
(1) First. Using the table of contents, determine
turer, distributor, or Government agency, etc.
the functional group within which the item belongs.
e. Part Number. Indicates the primary number
This is necessary since illustrations are prepared for
used by the manufacturer (individual company,
functional groups and listings are divided into the
firm, corporation or Government activity), which
controls the design and characteristics of the item by
(2) Second. Find the illustration covering the
means of its engineering drawings, specifications,
functional group to which the item belongs.
standards, and inspection requirements to identify
(3) Third. Identify the item on the illustration
an item or range of items.
and note the illustration figure and item number of
When a stock numbered item is requisi-
(4) Fourth. Using the Repair Parts Listing, find
tioned, the repair part received may have a
the figure and item number noted on the illustration.
different part number than the part being
b. When National stock number or part number is
(1) First. Using the index of National Stock
f. Description. Indicates the Federal item name
and if required, a minimum description to identify
Numbers and Part Numbers, find the pertinent
National stock number or part number. This index is
in NIIN sequence followed by a list of part numbers
g. Unit of Measure (U/M). Indicates the standard
of the basic quantity of the listed item as used in
in alphanumeric sequence, cross-referenced to the illus-
tration figure number and item number.
performing the actual maintenance function. This
measure is expressed by a two-character alphabetical
(2) Second. After finding the figure and item
abbreviation (e.g., ea, in, pr, etc). When the unit of
number, locate the figure and item number in the
measure differs from the unit of issue, the lowest unit
repair parts list.
of issue that will satisfy the required units of mea-
sure will be requisitioned.
h. Quantity Incorporated in Unit. Indicates the
quantity of the item used in the breakout shown on
(Next printed page is 4)